1¢ Franklin Issue of 1851 Plate 1 early Intro

1¢ Franklin Issue of 1851-1857, PLATE 1 EARLY
Plate 1 Early State - Introduction and Characteristics.

The Second Series of US Stamps
Three new stamps—One, Three and Twelve-cent denominations—were deemed necessary after postage rates were revised by Congress during the Fillmore administration. Effective July 1, 1851, the basic rates became 1c for newspapers and circulars (with a distance escalation until 1852), 1c for drop letters, 3c for domestic letters sent up to 300 miles, and 6c for letters sent over 300 miles. One very important aspect of the July 1st change was that the new rates were for PREPAID mail (eg. letter rate 3¢), and unpaid letters still cost 5¢. This 40% inducement to prepaid (in cash or by stamps) was a big reason stamp usage rapidly increased. Prepayment by stamps or stamped envelopes was not compulsory until 1856, but the convenience of stamps and reduction in rates led to a rapid increase in stamp usage and popularity.

Ten Years of Printing
Under Postmaster General Nathan K. Hall, the contract to print the 1851 Issue was awarded to one of Rawdon, Wright, Hatch & Edson’s competitors, the Philadelphia firm of Toppan, Carpenter, Casilear & Co. (Casilear retired in October 1854; his name was included in plate imprints as late as 1857). The firm’s original six-year contract was extended to 1861, during which time stamps of only eight different denominations were issued. However, due to the volume and irregularity of production, as well as the introduction of perforations in 1857, the Scott Catalogue has 44 different major listings, based on color, perforation and design variation (excluding sub-listings and the 1875 Reprints).

So Many Types, So Little Time
The 1c 1851-61 stamp, with a bust of Franklin based on Caffieri’s sculpture, dominates this group with 18 major listings. No other 19th century United States stamp has so many type classifications. The explanation for the variation in 1c 1851-57 stamps is simple: the basic design was too large to fit on the printing plate. The design on the master die, with all of its elaborate ornamentation, was intended to be fully replicated in each of the 200 subjects. However, in transferring the design from the master die to the plate via the transfer roll, the craftsmen responsible for making plates discovered that ten rows of the full design could not fit into the designated area. To correct the problem the reliefs on the transfer roll were shortened and/or parts of the entries on the plate were burnished away to make space for the next subject.

Plate One Early
One cent stamps were printed from twelve plates between 1851 and 1861. Plate 1 was first placed in service in July 1851 and was the only plate used until mid 1857. The plate is very interesting because after being used for 11 months, sufficient wear occurred that it was reentered and recut. While the first or early state of the plate produced stamps of Type I, Ib, II and IIIa, the second state of the plate was recut to produce Type IV stamps in 199 positions and a single Type II. These two states of the plate are referred to as plate 1 early and plate 1 late. Imperforate stamps only were printed with plate 1 early; both imperforate stamps and perforated stamps were produced from plate 1 late.

Reliefs
Plate No. 1 of the one cent was in all probability the second stamp plate made by Toppan, Carpenter, Casilear & Co. after they received the government contract in 1851. We call the relief roller used to complete the plate, transfer roller No. 1, and the three reliefs - Relief "T," Relief "A," and Relief "B." It is essential for the plating student to be able to identify the relief. This sometimes can be difficult on poorly centered stamps with the designs cutoff on either the top or bottoms.

Fine Plate Scratches

B Relief Guide Dots

Centerline

Double Transfers

12 Plates of Fun
The 1c plate-making process was further complicated by reentries and double transfers, wear over many thousands of impressions, the development of cracks and flaws in the metal, the reworking of the first plate used, and the need to accommodate perforations in 1857. Over ten years a total of 12 plates were made and one plate (Plate 1) was reentered and recut to improve its worn appearance. Plates 1 (Early) and 3 produced imperforate stamps exclusively. Plates 1 (Late) and 2 produced imperforate stamps for the most part, but sheets from these two plates were also perforated. Plate 4, used only in 1857, produced a small quantity of imperforate stamps and a large portion of the perforated stamps issued from July to December 1857. Plates 5 through 12 produced perforated stamps exclusively. Plate 6 was produced but was never used to print stamps as, no stamps from Plate 6 have ever been identified. Researchers believe Plate 6 was damaged while it was being made.

It's All About Details
The designated types of 1c stamps are based on the resulting printed design after the die-to-relief-to-plate transfer process and the alterations made to the plate entries (principally burnishing and recutting). Philatelists look for certain features: Is the design complete? Is it complete just at top or bottom? Are the outer lines intact or broken? Were the outer lines recut? The rarity and value of 1c 1851-61 stamps are determined by the types and variations produced by 2,400 different subjects on 12 plates (including Plate 1 Late) over a decade. Because specific types, or Scott numbers, are produced by a certain number of positions on one or more plates, the quantity produced of any particular Scott number relates directly to the quantity printed from the corresponding plate or plates.

The Rarest of Them All
For example, Scott number 5 is the only Type I imperforate, which shows the design complete at top and bottom. Of the five plates used to print imperforate 1c stamps, just one out of 1,000 positions, the 7th stamp in the right pane of Plate 1 Early (7R1E), was entered with the design complete at top and bottom (Type I) and remained unburnished. The number of Type I (7R1E) imperforate stamps printed relative to all others is a tiny fraction when the brief production period for Plate 1 Early is factored into the equation. Ashbrook estimated that fewer than 36,000 Type I imperforate stamps were ever printed. Today, there are perhaps 100-110 copies known to exist.

DISCLAIMER and COPYRIGHT INFORMATION:
Thanks for visiting this site. I hope you learn something new as we are making new discoveries all the time. You, the visitor, have my permission to link to my pages and to share the INFORMATION with others. The images themselves fall under the fair use guidelines established by the United States Congress and Copyright law. Basically contact us before using. I also ask in return that you send me an e-mail if I have made a mistake, or have made some other technical blunder that in my rush to put these pages up would cause the visitor confusion. Please also visit my other website at www.slingshotvenus.com. and support the live music arts. While your there, be sure to purchase our music. There are not many philatelic rock stars around and we need all the help we can get. :-)

UPDATE: 8.31.2010